15 June 2000

MiniatureZone Gallery Archives (2000 - 2006) - Tony Ivey - Krupp Raumer-S

This article is one of many articles and gallery contributions from fellow amateur smallscale enthusiasts all over the world that appeared on the old MiniatureZone website during the first six years its existence when there were only a handful of websites dedicated to smallscale models and wargaming. 

If you've been around on the internet since back then, we hope you like the nostalgia, and if you´re a newcomer, hope you enjoy looking too.



MiniatureZone Gallery Archives (2000 - 2006) - Tony Ivey - Krupp Raumer-S







From the beginning I decided to make it articulate. I have never done anything like this before, so it was my initiation. I copied the design of the supplied pieces and just used some sheet styrene, brass tube and piano wire for the pins. It took a while, but I like the results.

This vehicle was almost completed at the end of the war. Built by Krupp, it had a crew of 8 including the 2 drivers. The heavy weight of each section was enough to detonate all mines in it's path. Each section could tilt 22 degrees against each other.

It was found at Hillersleben, Germany at the end of the war by Americans. There are currently only about 3 pictures of it. I have heard that there will be a book coming out soon on it, since some information became declassified.

Hope you like...Tony Ivey USA



Copyright Tony Ivey, 15th June 2000

MiniatureZone Gallery Archives (2000 - 2006) - Tony Ivey - Schwimmkorper auf 38(t) Praga

This article is one of many articles and gallery contributions from fellow amateur smallscale enthusiasts all over the world that appeared on the old MiniatureZone website during the first six years its existence when there were only a handful of websites dedicated to smallscale models and wargaming. 

If you've been around on the internet since back then, we hope you like the nostalgia, and if you´re a newcomer, hope you enjoy looking too.



MiniatureZone Gallery Archives (2000 - 2006) - Tony Ivey - Schwimmkorper auf 38(t) Praga : 





The floatation device was tested in February 1941 and consisted of a large, boat-like float AP-1, fitted around the tank. Two propellers in the rear were connected to the tank's engine and in calm water the prototype attained speeds of  up to 8 km/hour. The adaptation was rugged enough for ocean use, but it is not known for what operation it was considered. (Source : Schiffer's "Czechoslovak Armored Fighting Vehicles 1918-1948", page 205)


Hope you like...Tony Ivey USA



Copyright Tony Ivey, 15th June 2000

01 March 2000

Making a Stone Bridge from Styrofoam

Making a Stone Bridge from Styrofoam



Bridges often form an important focal point or strategic element in a game, and can also often make attractive centrepieces for interesting dioramas.

Building from scratch is not too difficult and the object of this article is demonstrate how to build a simple but effective representations of these stone bridges.

Construction materials 
  • EPS foamboard, also known as “Styrofoam” 
  • Cereal box or stiff card 
  • 1 sheet of paper 
  • PC & laser / injket printer 
  • Scissors 
  • Craft Knife 
  • Ball-point pen 
  • White glue 
  • Black, grey, white acrylic paints (or other colours according to preferences) 
  • Very fine sand (optional) 
The main material used to make our bridge here is EPS foamboard (greatly superior to expanded polystyrene) because it’s compact, can easily be cut without crumbling and is durable. You can buy it in sheets at hardware stores (a well known brand is called “Depron”) but you can also use the same stuff that little trays are made of that you find in supermarkets to pack fruit or meat.

Making a Master

In order to make the bridge we’ll first need a master and making this isn’t particularly difficult, though it can be a little time consuming.

For a basic bridge we need to make four templates from very simple shapes as shown here. If you click on the image below it will open in a new window. You can download and print the template onto A4 paper.




Construction

Print your masters onto a sheet of A4 size paper, then with a pair of scissors cut the templates out. The sides of the bridge and the base sections will be made from foamboard, so we’ll use shapes we’ve cut from paper as templates Place these templates onto the foamboard and lightly draw around them with a ball-point pen and then with a sharp craft knife cut the foamboard along the pen lines.







Now all we have to do to represent a stone pattern is to draw it on with a ball-point pen



We need to make the pattern convincing so it’s important to take a little time doing this.

Best not to use anything sharp to do this, you´ll need to use a ball-point pen because instead of scratching on a design, we have to leave an imprint and the ball-point pen “glides” across the foamboard.

Once we’ve got the stone pattern finished then we can assemble the bridge. 

Stick the two sides of the bridge to the bases with white glue and wait for it to dry overnight so it’s fixed well.




The next stage is to make the road section from stiff card,making sure that it curves without any creases and just stick with white glue (a bit tricky and you might have to hold this for quite until it’s stuck well). Finally the last piece to glue the underside of the bridge’s arch.





Painting

Painting is a matter of personal taste and everyone has their own techniques and preferences. I used artist’s latex based paints that you can buy from hobby shops, starting with undiluted black paint then mixing in some very very fine sand and once you have this mixture ready paint all over the bridge and leave to dry for a few hours.

Once the black paint is dry, take a suitable stone colour and give the bridge and roadway an extremely heavy drybrush and you’ll see that the stone pattern becomes very nicely defined due to the black undercoat staying in the recesses of the pattern - it should now resemble a stone bridge. Just to finish off give a final very light drybrush with some white or other very light paint according to your preferences.

The only other thing I added was a border of grass and small rocks along the side of the base as you can see in the picture at the top of this article.

10 January 2000

Esci Opel Blitz Ambulance

Esci Opel Blitz Ambulance - Diorama by Stephen Brezinski




By Stephen Brezinski, Maine USA (10/01/2000) (original article formerly on the miniaturezone.co.uk website)


The vehicle is a 1/72 ESCI Opel Blitz truck, painted in dunkelgelb with a green camoflage pattern. This vehicle was one of the most common German 3-ton trucks, produced in either a 4x4 or 4x2 version. Besides fuel and cargo versions, the van variant was common and used for ambulances, command,and communications vehicles. The van could even be seen on the tracked Maultier (Mule) version of the truck.





I opened up the rear doors and added four bunks using the stretchers from two ESCI SdKfz 251 ambulance kits, a desk/operating table, seat, and various boxes and bedrools. Windows were also opened up and clear sheet styrene glued in with Kristal Clear. Inside I also scribed in the door panels to match those on the outside walls of the van. Wood steps were created from a model RR kit.


The markings and license plates are decals from the kit, set down with Solveset. Clear windows and windshield was also cut and added to the cab. There were fit problems with the cab which required careful fit and putty. Also added to the cab was a rearview mirror, wipers, and width indicators on the fenders.


The grass was created with model RR flocking. The figures sitting, table, and chairs are from Preiser's 1/72 tank repair personnel (in hard, polystyrene plastic)








Most all the paint used were acrylics, though the flesh tones are enamel which can be blended a bit with a brush dampened with thinner. Overall the kit can be challenging but looks great when the fit is corrected. The figures are superb and I hope more are released.

--------------------------------------------------------------------------------


© Stephen Brezinski, Maine USA


10/01/2000